Pelco Marine Sanitation System CM9760 KBD E80 User Manual

I N S T A L L A T I O N M A N U A L  
System 9760®  
KBD/KBR Firmware  
Upgrade  
®
CM9760-KBD-E80  
C1543M-A (7/04)  
 
INTRODUCTION  
The System 9760® keyboard upgrade kit, CM9760-KBD-E80, provides the following items to upgrade CM9760-KBD/CM9760-KBR  
firmware to version 8.03:  
1
1
U3 EPROM chip, version 8.03, part number IC53-0043-0803  
Chip extraction tool, part number ICPULLERTOOL  
This manual provides instructions to upgrade CM9760-KBD/CM9760-KBR firmware from version 7.8 or earlier to version 8.03.  
To upgrade CM9760-KBD firmware, see the section titled Upgrading CM9760-KBD Firmware. To upgrade CM9760-KBR  
firmware, see the section titled Upgrading CM9760-KBR Firmware.  
C1543M-A (7/04)  
1
 
UPGRADING CM9760-KBD FIRMWARE  
CAUTION: Only qualified personnel observing electrostatic discharge (ESD) precautions should perform the procedure  
below. Always wear a grounding strap connected to an approved grounding source when working on or near exposed  
electronic components. Handle circuit boards by their edges.  
To upgrade CM9760-KBD firmware to version 8.03, do the following:  
1. Using System Manager, upload user-entered keyboard setup information to the System Manager database.  
NOTE: This step is necessary to avoid loss of user-programmed keyboard setup information, which is erased when  
the KBD is reset later in this procedure. After the KBD is reset, you can download the setup information from  
System Manager to the KBD as directed later in this procedure.  
2. Log off the KBD and then turn the KBD over so that the bottom of the KBD is visible (refer to Figure 1).  
3. Disconnect the KBD from the 9760 system by unplugging the cable from the COM 1 port of the KBD.  
4. Set DIP switch 7 to the correct position:  
For compatibility with CM9760-CC1 and CM9760-MGR versions 7.80.003 to 7.80.029, set DIP switch 7 to the OFF  
position.  
For compatibility with CM9760-CC1 and CM9760-MGR version 8.03.006 or later, set DIP switch 7 to the ON position.  
5. Remove the bottom cover of the KBD:  
a. Unscrew nine Phillips screws as indicated in Figure 1. Note that on some KBDs one of the screws has a plastic  
retaining nut as indicated in Figure 1. Remove that screw after you remove the other eight screws.  
To remove the screw that has a plastic retaining nut, do the following:  
(1) Lift off the bottom cover of the KBD slightly.  
(2) Locate the nut and, while holding the nut with your fingers to prevent the nut from turning, remove the screw.  
b. Gently lift off the bottom cover of the KBD.  
CAUTION: Be careful not to detach any of the wires that are soldered to the surface of the circuit board.  
(MAY HAVE  
RETAINING  
CABLE  
SCREW (9)  
NUT)  
DIP SWITCH 7  
Volume  
Options  
Relay  
Com3 Com2  
Com1  
Reset  
NO  
Figure 1. Bottom of CM9760-KBD  
2
C1543M-A (7/04)  
 
6. Remove the existing U3 EPROM chip (refer to Figure 2) from its socket using the provided extraction tool. Remove the chip  
slowly to avoid damaging the socket.  
7. Remove the replacement EPROM chip from the electrostatic bag, and inspect the chip to confirm that the pins are  
straight.  
8. As illustrated in Figure 2, orient the chip using the alignment notch as a guide. Verify pin-to-socket alignment, and then  
carefully press the chip into its socket until the chip is completely seated.  
9. Reattach the bottom cover to the KBD using the nine Phillips screws.  
10. Reset the keyboard to factory default settings by doing the following:  
a. With the KBD remaining powered off, set DIP switches 1, 2, and 8 to the ON position.  
b. Power on the KBD by reconnecting the cable to the COM 1 port.  
The Diagnostics mode display appears.  
c. Power off the KBD by disconnecting the cable from the COM 1 port.  
d. Set DIP switches 1 and 8 to the OFF position.  
e. Power on the KBD by reconnecting the cable to the COM 1 port.  
U4  
U12 U2  
U3  
U5  
NOTCHED END  
OF EPROM  
CIRCUIT  
BOARD  
ALIGNMENT  
NOTCH  
U3 EPROM CHIP  
Figure 2. U3 EPROM Chip  
C1543M-A (7/04)  
3
 
11. Calibrate the joystick as follows:  
a. In Setup mode, select the Joystick Adjust icon.  
The Joystick Setup menu appears (refer to Figure 3).  
EXIT ICON  
KEYBOARD  
SELECT  
ICON  
FORWARD STEP/  
SCROLL UP  
ICON  
BACKWARD STEP/  
SCROLL DOWN  
ICON  
MOVE CURSOR/  
CYCLE SELECTIONS CYCLE SELECTIONS  
LEFT ICON RIGHT ICON  
MOVE CURSOR/  
SAVE ICON  
Figure 3. Joystick Setup Menu  
b. With the joystick in the central default position, select the Keyboard Select icon.  
c. Verify that the pan and tilt center values (xxx,xxx) are between 122 and 134.  
d. Move the joystick fully to the left, and then select the Move Cursor/Cycle Selections Left icon.  
e. Verify that the left value is between 90 and 98.  
f. Move the joystick fully to the right, and then select the Move Cursor/Cycle Selections Right icon.  
g. Verify that the right value is between 158 and 166.  
h. Move the joystick fully down, and then select the Backward Step/Scroll Down icon.  
i.  
j.  
Verify that the down value is between 90 and 98.  
Move the joystick fully up, and then select the Forward Step/Scroll Up icon.  
k. Verify that the up value is between 158 and 166.  
l. Save the joystick configuration by selecting the Save icon.  
m. Return to the Setup menu by selecting the Exit icon.  
12. Using System Manager, download the keyboard setup information to the KBD.  
4
C1543M-A (7/04)  
 
UPGRADING CM9760-KBR FIRMWARE  
CAUTION: Only qualified personnel observing electrostatic discharge (ESD) precautions should perform the procedure  
below. Always wear a grounding strap connected to an approved grounding source when working on or near exposed  
electronic components. Handle circuit boards by their edges.  
To upgrade CM9760-KBR firmware to version 8.03, do the following:  
1. Using System Manager, upload user-entered keyboard setup information to the System Manager database.  
NOTE: This step is necessary to avoid loss of user-programmed keyboard setup information, which is erased when  
the KBR is reset later in this procedure. After the KBR is reset, you can download the setup information from  
System Manager to the KBR as directed later in this procedure.  
2. Log off the KBR.  
3. Disconnect the KBR from the 9760 system by unplugging the cable from the COM 1 port on the rear of the KBR (refer to  
Figure 4).  
4. Remove the KBR from the rack by unscrewing the two Phillips rack-mounting screws from each rack ear on the front of  
the KBR (refer to Figure 5).  
PAN HEAD SCREW (4)  
FLAT HEAD SCREW (16)  
DIP SWITCH 7  
Volume  
Options  
Relay  
I2  
C
Com3 Com2  
Com1 Reset  
Volume  
Reset  
NO  
Options  
CABLE  
Figure 4. Rear of CM9760-KBR  
RACK  
RACK-MOUNTING  
SCREW (4)  
Figure 5. Front of CM9760-KBR  
C1543M-A (7/04)  
5
 
5. Locate DIP switch 7 on the rear of the KBR (refer to Figure 4), and set the DIP switch to the correct position:  
For compatibility with CM9760-CC1 and CM9760-MGR versions 7.80.003 to 7.80.029, set DIP switch 7 to the OFF  
position.  
For compatibility with CM9760-CC1 and CM9760-MGR version 8.03.006 or later, set DIP switch 7 to the ON position.  
6. Remove the rear panel of the KBR by unscrewing 16 flat head and 4 pan head Phillips screws (5 flat head screws on top  
of panel, 5 flat head screws on bottom of panel, 3 flat head screws on each side of panel, and 4 pan head screws on face  
of panel).  
7. Remove the existing U3 EPROM chip (refer to Figure 6) from its socket using the provided extraction tool. Remove the chip  
slowly to avoid damaging the socket.  
8. Remove the replacement EPROM chip from the electrostatic bag, and inspect the chip to confirm that the pins are  
straight.  
9. As illustrated in Figure 6, orient the chip using the alignment notch as a guide. Verify pin-to-socket alignment, and then  
carefully press the chip into its socket until the chip is completely seated.  
10. Reattach the rear panel of the KBR using the 16 flat head and 4 pan head Phillips screws.  
11. Reset the keyboard to factory default settings by doing the following:  
a. With the KBR remaining powered off, set DIP switches 1, 2, and 8 to the ON position.  
b. Power on the KBR by reconnecting the cable to the COM 1 port.  
The Diagnostics mode display appears.  
c. Power off the KBR by disconnecting the cable from the COM 1 port.  
d. Set DIP switches 1 and 8 to the OFF position.  
e. Power on the KBR by reconnecting the cable to the COM 1 port.  
U4  
U12 U2  
CIRCUIT  
BOARD  
U3  
U5  
NOTCHED END  
OF EPROM  
ALIGNMENT  
NOTCH  
U3 EPROM CHIP  
Figure 6. U3 EPROM Chip  
6
C1543M-A (7/04)  
 
12. Calibrate the joystick as follows:  
a. In Setup mode, select the Joystick Adjust icon.  
The Joystick Setup menu appears (refer to Figure 7).  
EXIT ICON  
KEYBOARD  
SELECT  
ICON  
FORWARD STEP/  
SCROLL UP  
ICON  
BACKWARD STEP/  
SCROLL DOWN  
ICON  
MOVE CURSOR/  
CYCLE SELECTIONS CYCLE SELECTIONS  
LEFT ICON RIGHT ICON  
MOVE CURSOR/  
SAVE ICON  
Figure 7. Joystick Setup Menu  
b. With the joystick in the central default position, select the Keyboard Select icon.  
c. Verify that the pan and tilt center values (xxx,xxx) are between 122 and 134.  
d. Move the joystick fully to the left, and then select the Move Cursor/Cycle Selections Left icon.  
e. Verify that the left value is between 90 and 98.  
f. Move the joystick fully to the right, and then select the Move Cursor/Cycle Selections Right icon.  
g. Verify that the right value is between 158 and 166.  
h. Move the joystick fully down, and then select the Backward Step/Scroll Down icon.  
i.  
j.  
Verify that the down value is between 90 and 98.  
Move the joystick fully up, and then select the Forward Step/Scroll Up icon.  
k. Verify that the up value is between 158 and 166.  
l. Save the joystick configuration by selecting the Save icon.  
m. Return to the Setup menu by selecting the Exit icon.  
13. Mount the KBR into the rack, and attach each rack ear of the KBR to the rack using two Phillips rack-mounting screws for  
each ear.  
14. Using System Manager, download the keyboard setup information to the KBR.  
C1543M-A (7/04)  
7
 
 
WARRANTY AND RETURN INFORMATION  
WARRANTY  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981  
to obtain a Repair Authorization number (RA), and provide the following information:  
Pelco will repair or replace, without charge, any merchandise proved defective in material  
or workmanship for a period of one year after the date of shipment.  
1. Model and serial number  
Exceptions to this warranty are as noted below:  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2,  
CC3651H-2X, MC3651H-2, and MC3651H-2X.  
If there is a dispute regarding the warranty of a product which does not fall under the warranty  
conditions stated above, please include a written explanation with the product when returned.  
Three years on all other fixed camera models (including Camclosure® Integrated  
Camera Systems) and Genex® Series (multiplexers, server, and keyboard).  
Two years on all standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM8500/CM9500/CM9700 Series Matrix,  
DF5 and DF8 Series Fixed Dome products.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous  
motion applications.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)  
289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,  
and RA number if returned for repair).  
Two years on Esprit® and WW5700 series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders and NVR300 network video  
recorders.  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number  
and freight should be prepaid. Ship to the appropriate address below.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or  
accident are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to  
return goods to the USA, you may do one of the following:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelco’s liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
If the goods are to be sent by a COURIER  
SERVICE, send the goods to:  
Pelco  
If the goods are to be sent by a FREIGHT  
FORWARDER, send the goods to:  
Pelco c/o Expeditors  
3500 Pelco Way  
473 Eccles Avenue  
Clovis, CA 93612-5699 USA  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
The above warranty provides the Dealer with specific legal rights. The Dealer may also  
have additional rights, which are subject to variation from state to state.  
Fax: 650-737-0933  
REVISION HISTORY  
Manual #  
C1543M  
C1543M-A  
Date  
4/03  
7/04  
Comments  
Original version  
Added factory-default reset and joystick calibration information  
Pelco, the Pelco logo, and System 9760 are registered trademarks of Pelco.  
© Copyright 2004, Pelco. All rights reserved.  
 
®
World Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada Singapore  
 

Pentair Universal Remote LX 80 User Manual
Pentax GPS Receiver WG 1 User Manual
Pioneer DVD Player DV 434 User Manual
Planar Computer Monitor PL1711M User Manual
Planet Technology Network Router WAP 4030A User Manual
Poulan Chainsaw PN3312 User Manual
Poulan Lawn Mower PR1842STA User Manual
Poulan Trimmer 952711879 User Manual
Powermate Portable Generator PM0538000 User Manual
PSC Scanner PowerScanTM RF User Manual