Pelco Scanner C361M A User Manual

®
PS20 Medium-Duty  
Indoor/Outdoor Scanner  
Installation/  
Operation Manual  
C361M-A (8/02)  
Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.pelco.com  
USA & Canada: Tel: 800/289-9100 • Fax: 800/289-9150  
International: Tel: 1-559/292-1981 • Fax: 1-559/348-1120  
 
PREPARE MOUNTING SURFACE  
NOTE: Minimum recom-  
mendation for mounting  
hardware is 1/4-20 X 5/8 Hex  
Head Bolt Stainless Steel,  
1/4" Split Lock Washer Stain-  
less Steel, and 1/4" Flat  
Washer Stainless Steel with  
1" Outer Diameter.  
1. Determine the mounting location. Make sure the mounting surface can support four  
times the combined weight of the scanner and the camera and lens or enclosure,  
camera, and lens. Refer to the manuals for your enclosure, camera, and lens for the  
weights of those units.  
2. If mounting directly to a flat surface, use Figure 1 as a template and mark the bolt and  
cable/wire feedthrough positions onto the installation surface. Prepare the mounting  
surface and pull cable/wiring for the scanner.  
BOLT  
HOLE  
SCANNER  
BOLT  
BOLT  
HOLE  
FEED THRU  
HOLE  
HOLE  
BOLT  
HOLE  
00814  
Figure 1. PS20 Surface Mount Template  
Pelco Manual C361M-A (8/02)  
3
 
WIRING  
Make electrical connections as required for scanner  
operation. If required use the wire nuts (provided).  
Cable distances should not exceed the distances  
specified in Table A.  
Refer to the following wiring diagrams (Figure 3)  
and select the correct diagram for your installation.  
GLAND AND WIRING  
ATTACHMENT  
Figure 2. Bottom View, Wire  
Attachment  
120V MODEL  
24V MODEL  
230V MODEL  
WITH CONTROLLER  
WITH CONTROLLER  
WITH CONTROLLER  
BLU  
BRN  
ORG  
RED  
WHT  
GRN/YEL  
BLK  
BLU  
BRN  
ORG  
RED  
WHT  
GRN/YEL  
BLK  
WHT  
BLK  
ORG  
RED  
BLU  
GRN/YEL  
BRN  
COMMON  
LEFT  
RIGHT  
COMMON  
LEFT  
RIGHT  
COMMON  
LEFT  
RIGHT  
CABLE  
FROM  
SCANNER  
CABLE  
FROM  
SCANNER  
CABLE  
FROM  
SCANNER  
AUTO  
AUTO  
AUTO  
120 AC LO  
GROUND  
120 AC HI  
24 AC LO  
GROUND  
24 AC HI  
230 AC LO  
GROUND  
230 AC HI  
WITHOUT CONTROLLER  
WITHOUT CONTROLLER  
WITHOUT CONTROLLER  
WHT  
GRN/YEL  
BLK  
RED  
BLU  
BRN  
ORG  
WHT  
GRN/YEL  
BLK  
RED  
BLU  
BRN  
ORG  
BLU  
GRN/YEL  
BRN  
RED  
WHT  
ORG  
BLK  
120 AC LO  
GROUND  
120 AC HI  
AUTO  
120 AC LO  
NOT USED  
NOT USED  
24 AC LO  
GROUND  
24 AC HI  
AUTO  
120 AC LO  
NOT USED  
NOT USED  
230 AC LO  
GROUND  
230 AC HI  
AUTO  
120 AC LO  
NOT USED  
NOT USED  
CABLE  
FROM  
SCANNER  
CABLE  
FROM  
SCANNER  
CABLE  
FROM  
SCANNER  
RANDOM MODE  
RANDOM MODE  
RANDOM MODE  
WHT  
GRN/YEL  
BLK  
RED  
ORG  
WHT  
GRN/YEL  
BLK  
RED  
ORG  
BLU  
GRN/YEL  
BRN  
RED  
BLK  
120 AC LO  
GROUND  
120 AC HI  
24 AC LO  
GROUND  
24 AC HI  
230 AC LO  
GROUND  
230 AC HI  
CABLE  
FROM  
SCANNER  
CABLE  
FROM  
SCANNER  
CABLE  
FROM  
SCANNER  
BRN  
BRN  
ORG  
BLU  
BLU  
WHT  
00815  
Figure 3. Wiring Diagrams - 120V, 24V and 230V Models  
Table A. Maximum Operating Distances  
Model  
20 AWG  
(0.5 mm2)  
18 AWG  
(1.0 mm2)  
16 AWG  
(1.5mm2)  
PS20  
2,300 ft  
(701 m)  
3,700 ft  
(1,127 m)  
5,900 ft  
(1,798 m)  
PS20-24  
PS20/23  
5,600 ft  
(1,706 m)  
9,000 ft  
(2,743 m)  
14,300 ft  
(4,368 m)  
1,400 ft  
(426 m)  
2,300 ft  
(701 m)  
3,600 ft  
(1,097 m)  
4
Pelco Manual C361M-A (8/02)  
 
MOUNTING  
Attach the scanner to a flat surface or compatible wall/ceiling/pedestal mount using four  
bolts (not provided).  
CAMERA/ENCLOSURE MOUNTING  
1. Center (balance) the camera and lens, or enclosure, camera, and lens load on the tilt  
table. Adjust the positioning as needed to align the mounting holes.  
2. Attach the camera or enclosure to the tilt table with two 1/4-20 hex head bolts (not  
supplied).  
3. Position the tilt table at the desired angle and tighten the manual tilt adjustment bolts  
(refer to Figure 3) to secure the table.  
4. Make all camera, enclosure, and lens connections. Refer to the manuals supplied with  
the equipment. Leave enough slack in the cable/wiring so that the camera, enclosure,  
and lens connections do not interfere with the operation of the scanner.  
SPEED SETTING  
The PS20 Series scanner has selectable speed settings for 3 degrees, 6 degrees, and 12  
degrees per second. The default speed setting is 6 degrees per second. To decrease or  
increase the speed setting do the following:  
1. Loosen the screw that secures the speed setting cover. The cover is located on the  
side of the scanner (refer to Figure 3).  
2. Remove the speed setting cover.  
3. Set the switch to the desired speed setting.  
4. Replace the cover and tighten the screw.  
TILT TABLE  
MANUAL TILT  
ADJUSTMENT  
BOLT  
3
6
12  
SPEED  
SETTINGS  
00813  
LIMIT STOP  
Figure 4. Scanner Adjustments and Settings  
Pelco Manual C361M-A (8/02)  
5
 
LIMIT STOP ADJUSTMENT  
To set pan limit stops, perform the following steps:  
1. Loosen the right and left limit stops.  
2. Operate the scanner. Pan the unit to the right until the desired right pan limit is  
reached.  
3. Move the right limit stop to the selected position and secure in place.  
4. Pan the unit to the desired left position. Slide the left limit stop to the selected position  
and secure in place.  
5. Pan left and right to both limit stops to check for exact positioning. Tighten both stops  
securely.  
To pan the scanner 380 degrees, remove one limit stop from the scanner. Only one limit  
stop is removable. The other limit stop is fixed to the scanner; it can be adjusted but not  
removed.  
6
Pelco Manual C361M-A (8/02)  
 
SPECIFICATIONS  
MECHANICAL  
Pan:  
0-380° movement in horizontal plane  
3°, 6°, or 12° per sec ±.5°  
35 lb (16 kg) centered  
Upright or inverted  
Heavy-duty ball bearings  
Speed:  
Maximum Load:  
Operation:  
Bearings:  
Overload Protection: Thermal protected  
ELECTRICAL  
Input Voltage  
PS20:  
PS20-24:  
120 VAC  
24 VAC  
PS20/230:  
Power Requirements  
PS20:  
230 VAC  
0.175 A (20 vA)  
PS20-24:  
0.600 A (15 vA)  
PS20/230:  
Connectors:  
Motors:  
Limit Switches:  
Conductors:  
0.130 A (30 vA)  
Wire nuts provided  
Stepper motor, continuous duty, instantaneous reversing  
Auto scan switching, external adjustment  
7, unshielded (functions: left, right, auto, common, safety ground,  
AC Line, AC Neutral)  
GENERAL  
Construction:  
Finish:  
Environment:  
Unit Weight:  
Aluminum  
Gray polyester powder coat  
Indoor/outdoor; -10° to 120°F (-23° to 49°C)  
9.9 lb (4.5 kg)  
Pelco Manual C361M-A (8/02)  
7
 
REGULATORY NOTICES  
This equipment has been tested and found to comply with the limits of a Class B digital  
device, pursuant to part 15 of the FCC rules. These limits are designed to provide  
reasonable protection against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may cause harmful interference to radio  
communications. However there is no guarantee that the interference will not occur in a  
particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user  
is encouraged to try and correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and the receiver.  
Connect the equipment into an outlet on a circuit different from that to which the re-  
ceiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
WARRANTY AND RETURN INFORMATION  
WARRANTY  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100  
or (559) 292-1981 to obtain a RepairAuthorization number (RA), and provide the  
following information:  
Pelco will repair or replace, without charge, any merchandise proved defective in  
material or workmanship for a period of one year after the date of shipment. Ex-  
ceptions to this warranty are as noted below:  
1. Model and serial number  
Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and  
MC3500/MC3600/MC3700 Series); two years on all other cameras.  
Three years on Genex® Series (multiplexers, server, and keyboard).  
Two years on cameras and all standard motorized or fixed focal length lenses.  
Two years on Legacy®, Camclosure® Camera Systems, CM6700/CM6800/  
CM8500/CM9500/CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome  
products.  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under  
the warranty conditions stated above, please include a written explanation with  
the product when returned.  
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in  
continuous motion applications.  
Method of return shipment shall be the same or equal to the method by which the  
item was received by Pelco.  
Two years on Esprit and WW5700 series window wiper (excluding wiper blades).  
Eighteen months on DX Series digital video recorders.  
One year (except video heads) on video cassette recorders (VCRs). Video heads  
will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous  
motion applications (that is, preset scan, tour and auto scan modes).  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call  
the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization num-  
ber (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and  
refurbishing charge.  
Pelco will warrant all replacement parts and repairs for 90 days from the date of  
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid  
to Pelco, Clovis, California. Repairs made necessary by reason of misuse,  
alteration, normal wear, or accident are not covered under this warranty.  
Goods returned for repair or credit should be clearly identified with the assigned  
CA or RA number and freight should be prepaid. Ship to the appropriate address  
below.  
Pelco assumes no risk and shall be subject to no liability for damages or loss  
resulting from the specific use or application made of the Products. Pelco’s liability  
for any claim, whether based on breach of contract, negligence, infringement of  
any rights of any party or product liability, relating to the Products shall not exceed  
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be  
liable for any special, incidental or consequential damages (including loss of use,  
loss of profit and claims of third parties) however caused, whether by the negligence  
of Pelco or otherwise.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico:  
Intermediate Consignee  
American Overseas Air Freight  
320 Beach Road  
Burlingame, CA 94010  
USA  
Ultimate Consignee  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
USA  
The above warranty provides the Dealer with specific legal rights. The Dealer may  
also have additional rights, which are subject to variation from state to state.  
REVISION HISTORY  
Manual #  
C361M  
C361M-A  
Date  
6/01  
8/02  
Comments  
Original version.  
Revised installation instructions. Added certifications.  
® Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco.  
© Copyright 2002, Pelco.  
All rights reserved.  
8
Pelco Manual C361M-A (8/02)  
 

Peavey Home Theater System 35XO User Manual
Peavey Music Mixer XR 700 User Manual
Pecoware Brush Cutter TBB 3000 User Manual
Pelco TV Mount EU3512 3X User Manual
Philips Breast Pump SCF304 User Manual
Philips CRT Television 13PR19C1 User Manual
Philips Home Theater System LX8320 User Manual
Philips TV Mount 32FWF1013 00 User Manual
PYLE Audio Car Stereo System PLCD94M User Manual
PYLE Audio Car Video System PLDN70U User Manual