Philips Home Theater System SWW1800 User Manual

Register your product and get support at  
SWW1800/27  
Quick Start Guide  
Connect  
1
Install  
2
Enjoy  
3
 
1
Connect  
Transmitter  
Receiver  
HDMI OUT  
DC IN 5V  
DC 5V  
2
1
HDMI OUT  
Connect the transmitter to your HD devices  
1
Connect video source to the transmitter using the HDMI cable  
Connect one end of the HDMI cable (included) to the HDMI connector of the  
transmitter.  
2
Connect the video source to the transmitter using the component cables  
Connect one end of the RCA (green, blue and red) cables to the Y/Pb/Pr IN  
connectors of the transmitter. Connect the other end of the RCA cables to the  
corresponding Y/Pb/Pr OUT connectors of your HD devices.  
Connect one end of the set of audio cables to the AUDIO L/R IN connectors  
of the transmitter. Connect the other end to the corresponding AUDIO L/R  
OUT connectors of your HD devices.  
3
Connect the power adaptor to the transmitter  
Connect one end of the power adapter (included) to the DC IN connector  
of the transmitter. Connect the other end of the power adaptor to a power  
socket.  
»
»
The power LED indicator lights up in solid red.  
The HDMI devices and analog devices with the component and stereo RCA start connecting.  
Connect the receiver to your HDTV set  
1
Connect the receiver with an additional HDMI cable (not included):  
Connect one end of the HDMI cable to the receiver.  
Connect the other end to the HDMI OUT connector of your HDTV.  
2
Connect the power adaptor to the receiver:  
Connect one end of the power adapter (included) to the DC IN connector of  
the receiver.  
Connect the other end of the power adaptor to a power socket.  
 
Install  
2
Install remote control batteries  
1
2
Open the battery compartment.  
Insert two AAA batteries with correct  
polarity (+/-) as indicated.  
3
Close the battery compartment.  
3
Enjoy  
DC 5V  
Turn on the power of your  
HDTV  
1
2
Go to the source menu under the settings menu of your HDTV.  
Select the HDMI input to which the receiver is connected.  
Note  
You cannot control the receiver with the supplied remote control and the  
receiver follows the transmitter’s status to enter/exit the standby mode.  
The synchronization of standby between the HDTV and the receiver  
depends on the capability of the HDTV.  
 
Switch on the transmitter  
Press on the remote control or transmitter in standby mode to turn it on.  
Select the source on the transmitter  
Press the source buttons: 1 HDMI , 2 HDMI, 3 INPUT, 4  
INPUT on the remote control or transmitter until you  
see the available video from your device.  
Note  
In standby mode, a red power LED displays on the  
transmitter .  
Depending on equipment and the input selected,  
between input selection/start-up and being able  
to see the image on your TV can take up to 15  
seconds.  
Wallmount the receiver  
You can either place the receiver near the HDTV or mount  
it on the wall.  
1
2
Choose a spot near the TV.  
Drill two holes in the wall. Ensure the distance  
between the two holes is 4.5mm.  
3
4
5
Punch the supplied plastic wall anchors into the two  
holes on the wall.  
Put the two screws into the plastic wall anchors and  
leave 3.2mm to mount the receiver on.  
Hook the receiver on the wall.  
 
Troubleshooting  
There is no video displayed on myTV screen.  
Verify the POWER LED and SOURCE LED indicator on the transmitter:  
I cannot hear any sound or the sound is poor, what do I do?  
Ensure the TV volume control is adjusted correctly.  
Ensure the TV volume is not set to minimum or the sound is not muted.  
Ensure the audio cables of the transmitter are connected correctly.  
Ensure the Audio format is recognized/supported.  
Long switching time due to the channel switching on a satellite/cable set-top box.  
Select video scaling if your set-top box supports this feature so as to keep the output  
resolution constant.  
Tip  
For more information, see the user manual.  
Welcome to Philips  
Register your product at www.philips.com/welcome  
Need help?  
User Manual  
Refer to the User Manual that came with your SWW1800.  
Online help  
© 2009 Koninklijke Philips Electronics N.V.All rights reserved. Reproduction in whole  
or in part is prohibited without the written consent of the copyright owner.  
Trademarks are the property of Koninklijke Philips  
Electronics N.V. or their respective owners.  
0682  
Printed inTaiwan  
SWW1800_27_EN_QSG_V1.1  
 

Pelco Home Security System C1303M B User Manual
Philips Electric Toothbrush HX6733 User Manual
Philips Projector Accessories BDL425IV User Manual
Philips Work Light P 2055 D User Manual
Pioneer CD Player DEH 3050UB User Manual
Pioneer MP3 Player DEH P670MP User Manual
Pioneer Stereo Receiver VSX C300 S User Manual
Pioneer Stereo System CDX FM1287 User Manual
Porter Cable Sander CL180PS User Manual
ProForm Home Gym PFB48030 User Manual